9 results
Search Results
Now showing 1 - 9 of 9
Article Citation - WoS: 3Citation - Scopus: 3Physical and Biological Characteristics of Electrospun Poly (vinyl Alcohol) and Reduced Graphene Oxide Nanofibrous Structure(Taylor & Francis Ltd, 2024) Sasmazel, Hilal Turkoglu; Alazzawi, Marwa; Gozutok, Melike; Sadhu, Veera; Turkoglu Sasmazel, HilalThe fabrication of graphene-based nanocomposites has been a topic of increasing interest due to graphene's exceptional physical properties and the ability to enhance the properties of various polymeric materials. Evaluating the biocompatibility of these nanocomposites is crucial to ensure their safe and effective use in biomedical applications. This study characterized and assessed the biocompatibility of previously fabricated electrospun polyvinyl alcohol (PVA)/reduced graphene oxide rGO fibrous structures by conducting a comprehensive assessment of their physical and biological characteristics. Contact angle measurements revealed that adding rGO to electrospun PVA fibers enhanced the surface wettability, improving the fibrous structure's PBS absorption capacity and degradation behavior. Including the rGO content resulted in a higher water vapor transmission rate, reaching similar to 48 g/m2day for PVA + 0.5 wt.% rGO and similar to 45 g/m2day for PVA + 1.0 wt.% rGO, compared to similar to 40 g/m2day for electrospun PVA fibers. Cell culture studies, including MTT assay, alkaline phosphatase (ALP) activity analysis, alizarin red staining, fluorescence microscopy, and SEM analyses, demonstrated that electrospun PVA + 1.0 wt.% rGO nanocomposites exhibited superior cell viability, proliferation, and growth compared to other samples, due to the improved physical properties of the PVA + 1.0 wt.% rGO fibrous structure.Article Citation - WoS: 25Citation - Scopus: 24Preparation of Electrospun Pcl-Based Scaffolds by Mono/Multi-functionalized Go(Iop Publishing Ltd, 2019) Basar, Ahmet Ozan; Sadhu, Veera; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalIn the present study, sythetic biodegradable polymer poly(epsilon-caprolactone) (PCL) and graphene oxide (GO) were combined together to prepare 3D, composite tissue scaffolds (PCL/GO scaffolds) by using electrospinning technique. Also, the influence of Gly-Arg-Gly-Asp-Ser-Pro (GRGDSP) and/or thiophene (Th) modified GO on the composite PCL/GO mats (PCL/GO, PCL/GO-GRGDSP, PCL/ GO-Th, PCL/GO-GRGDSP-Th) was further investigated. Characteristic examinations of the scaffolds were carried out by scanning electron microscope (SEM), contact angle (CA) measurements, x-ray photoelectron spectroscopy, TGA, electrical conductivity tests, phosphate buffer saline absorption and shrinkage tests and mechanical tests. All of the scaffolds were exhibited suitable bead free and uniform morphology according to SEM images. With the addition of GO, better hydrophilicity and a slight CA decrease (similar to 5 degrees) for the PCL/GO scaffolds were observed. Mechanical properties were reinforced drastically with the addition and well-dispersion of GO into PCL matrix. The incorporation of PCL and GO exhibited enhanced electrical conductivity and the highest value was found for PCL/GO-GRGDSP-Th (2%) as 15.06 mu S cm(-1). The MG-63 osteoblast cell culture studies (MTT assay, ALP activity, Alizarin-Red staining, fluorescence and SEM analyses) showed that PCL/GO-GRGDSP-Th (1%) scaffolds exhibited the highest biocompatibility performance (1.87 fold MTT absorbance value comparing with neat PCL) due to the advanced properties of GO and the biological interfaces.Article Citation - Scopus: 1Surface Patterning of Poly(ε-Caprolactone) Scaffolds by Electrospinning for Monitoring Cell Biomass Behavior(Springer, 2022) Albayrak, Deniz; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalThe aim of this work was to produce three-dimensional fibrous surface patterns of poly(epsilon-caprolactone) (PCL), onto two-dimensional smooth solvent cast PCL surfaces with an electrospinning method by using a mask/stencil for monitoring cell biomass behavior. The characterizations of produced scaffolds were done by thickness measurements, scanning electron microscopy (SEM) analyses, contact angle (CA) measurements, Fourier-transform infrared spectroscopy (FTIR), and mechanical tests. According to SEM micrographs, all of the electrospun scaffold surfaces exhibited bead-free and uniform morphology while solvent cast surfaces were smooth and nonporous. CA measurements revealed that the solvent cast surfaces had moderate hydrophilicity (similar to 60 degrees) while electrospun regions had a more hydrophobic character (similar to 110 degrees for fully electrospun surfaces and similar to 85 degrees for electrospun patterns). Mechanical testing showed the produced scaffolds had a brittle character. Moreover, cell culture studies were performed with mouse fibroblast (L929) cells for 7 days period, and cell attachment assay, MTT assay, fluorescence, and SEM analyses were done. Cell culture studies indicated that the solvent cast and electrospun patterns have different characteristics for cell behavior. Thus, cell movement, attachment, and proliferation can be directed and monitored by obtaining different surface topographies in a single substrate surface. Based on the results of this study, it was found that patterns consisting of polymeric nanofiber structures can also be created directly by the electrospinning method.Article Citation - WoS: 18Citation - Scopus: 19Effects of Nozzle Type Atmospheric Dry Air Plasma on L929 Fibroblast Cells Hybrid Poly (ε-caprolactone)/Chitosan (ε-Caprolactone) Scaffolds Interactions(Soc Bioscience Bioengineering Japan, 2016) Ozkan, Ozan; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalIn the study presented here, in order to improve the surface functionality and topography of poly (epsilon-caprolactone) (PCL)/chitosan/PCL hybrid tissue scaffolds fabricated layer by layer with electrospinning technique, an atmospheric pressure nozzle type plasma surface modification was utilized. The optimization of the plasma process parameters was carried out by monitoring the changes in surface hydrophilicity by using contact angle measurements. SEM, AFM and XPS analyses were utilized to observe the changes in topographical and chemical properties of the modified surfaces. The results showed that applied plasma modification altered the nanotopography and the functionality of the surfaces of the scaffolds. The modification applied for 9 min from a distance of 17 cm was found to provide the possible contact angle value (75.163 +/- 0.083) closest to the target value which is the value of tissue culture polystyrene (TCPS) petri dishes (similar to 49.7 degrees), compared to the unmodified samples (84.46 +/- 3.86). In vitro cell culture was carried out by L929 mouse fibroblast cell line in order to examine the effects of plasma surface modification on cell material interactions. Standard MIT assay showed improved cell viability on/within modified scaffolds confirmed with the observations of the cell attachment and the morphology by means of SEM, fluorescence and confocal imaging. The experiments performed in the study proved the enhanced biocompatibility of the nozzle type dry air plasma modified scaffolds. (C) 2016, The Society for Biotechnology, Japan. All rights reserved.Article Citation - WoS: 21Citation - Scopus: 18Dbd Atmospheric Plasma-Modified, Electrospun, Layer-By Polymeric Scaffolds for L929 Fibroblast Cell Cultivation(Taylor & Francis Ltd, 2016) Surucu, Seda; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalThis paper reported a study related to atmospheric pressure dielectric barrier discharge (DBD) Ar+O-2 and Ar+N-2 plasma modifications to alter surface properties of 3D PCL/Chitosan/PCL layer-by-layer hybrid scaffolds and to improve mouse fibroblast (L929 ATCC CCL-1) cell attachment, proliferation, and growth. The scaffolds were fabricated using electrospinning technique and each layer was electrospun sequentially on top of the other. The surface modifications were performed with an atmospheric pressure DBD plasma under different gas flow rates (50, 60, 70, 80, 90, and 100sccm) and for different modification times (0.5-7min), and then the chemical and topographical characterizations of the modified samples were done by contact angle (CA) measurements, scanning electron microscopy (SEM), atomic force microscopy, and X-ray photoelectron spectroscopy. The samples modified with Ar+O-2 plasma for 1min under 70cm(3)/min O-2 flow rate (71.077 degrees +/- 3.578) showed a 18.83% decrease compare to unmodified samples' CA value (84.463 degrees +/- 3.864). Comparing with unmodified samples, the average fiber diameter values for plasma-modified samples by Ar+O-2 (1min 70sccm) and Ar+N-2 (40s 70sccm) increased 40.756 and 54.295%, respectively. Additionally, the average inter-fiber pore size values exhibited decrease of 37.699 and 48.463% for the same Ar+O-2 and Ar+N-2 plasma-modified samples, respectively, compare to unmodified samples. Biocompatibility performance was determined with MTT assay, fluorescence, Giemsa, and confocal imaging as well as SEM. The results showed that Ar+O-2-based plasma modification increased the hydrophilicity and oxygen functionality of the surface, thus affecting the cell viability and proliferation on/within scaffolds.Article Citation - WoS: 9Citation - Scopus: 9Dielectric Barrier Discharge and Jet Type Plasma Surface Modifications of Hybrid Polymeric Poly (ε-caprolactone)/Chitosan Scaffolds(Sage Publications Ltd, 2018) Ozkan, Ozan; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalIn this study, dry air plasma jet and dielectric barrier discharge Ar+O-2 or Ar+N-2 plasma modifications and their effects on wettability, topography, functionality and biological efficiency of the hybrid polymeric poly (epsilon-caprolactone)/chitosan scaffolds were reported. The samples treated with Ar+O-2 dielectric barrier discharge plasma (80 sccm O-2 flow rate, 3-min treatment) or with dry air plasma jet (15-cm nozzle-sample distance, 13-min treatment) had the closest wettability (49.11 +/- 1.83 and 53.60 +/- 0.95, respectively) to the commercial tissue culture polystyrene used for cell cultivation. Scanning electron microscopy images and X-ray photoelectron spectrometry analysis showed increase in topographical roughness and OH/NH2 functionality, respectively. Increased fluid uptake capacity for the scaffolds treated with Ar+O-2 dielectric barrier discharge plasma (73.60%+/- 1.78) and dry air plasma jet (72.48%+/- 0.75) were also noted. Finally, initial cell attachment as well as seven-day cell viability, growth and proliferation performances were found to be significantly better for both plasma treated scaffolds than for untreated scaffolds.Article Citation - WoS: 57Citation - Scopus: 60Atmospheric Plasma Surface Modifications of Electrospun Pcl/Chitosan Hybrid Scaffolds by Nozzle Type Plasma Jets for Usage of Cell Cultivation(Elsevier Science Bv, 2016) Surucu, Seda; Masur, Kai; Sasmazel, Hilal Turkoglu; Von Woedtke, Thomas; Weltmann, Klaus Dieter; Turkoglu Sasmazel, HilalThis paper reports Ar gas, Ar + O-2, Ar + O-2 + N-2 gas mixtures and dry air plasma modifications by atmospheric pressure argon driven kINPen and air driven Diener (PlasmaBeam) plasma jets to alter surface properties of three dimensional (3D), electrospun PCL/Chitosan/PCL layer by layer hybrid scaffolds to improve human fibroblast (MRC5) cell attachment and growth. The characterizations of the samples were done by contact angle (CA) measurements, scanning electron microscopy (SEM), X-Ray Photoelectron spectroscopy (XPS) analysis. The results showed that the plasma modification carried out under dry air and Ar + O-2 + N-2 gas mixtures were altered effectively the nanotopography and the functionality of the material surfaces. It was found that the samples treated with Ar + O-2 + N-2 gas mixtures for 1 min and dry air for 9 min have better hydrophilicity 78.9 degrees + 1.0 and 75.6 degrees + 0.1, respectively compared to the untreated samples (126.5 degrees). Biocompatibility performance of the scaffolds was determined with alamarBlue (aB) assay and MTT assay methods, Giemsa staining, fluorescence microscope, confocal laser scanning microscope (CLSM) and scanning electron microscope (SEM) analyses. The results showed that plasma treated samples increased the hydrophilicity and oxygen functionality and topography of the surfaces significantly, thus affecting the cell viability and proliferation on/within scaffolds. (C) 2016 Elsevier B.V. All rights reserved.Article Citation - WoS: 6Citation - Scopus: 7Hybrid Polymeric Scaffolds Prepared by Micro and Macro Approaches(Taylor & Francis As, 2017) Ozkan, Ozan; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalPolymeric scaffolds with complex porous structures were fabricated with two different polymers by combining three fabrication methods in three steps, in which, nonwoven poly(e-caprolactone) microfibers were obtained with electrospinning and immersed in solvent cast chitosan solution poured in Petri dish to fabricate hybrid polymers, and finally the combined structure was freeze-dried with two different predrying techniques to obtain macropores in the structure. The resulting hybrid polymeric mats were found to have both microfibers and macroporosity due to the electrospinning as well as freeze-drying processes, which resemble the natural extracellular matrix. The optimized scaffolds that predried in the incubator at 40 degrees C for 5 h and then freeze-dried for 24 h exhibited contact angle value of 68.93 +/- 2.18 degrees with 3.252 +/- 0.783 MPa Young's modulus and 0.260 +/- 0.002 MPa yield strength as well as 1.35-fold cell yield in MRC5 fibroblast cell culture, compared to the commercial tissue culture polystyrene. [GRAPHICS] .Article Citation - WoS: 94Citation - Scopus: 97Development of Core-Shell Coaxially Electrospun Composite Pcl/Chitosan Scaffolds(Elsevier, 2016) Surucu, Seda; Sasmazel, Hilal Turkoglu; Turkoglu Sasmazel, HilalThis study was related to combining of synthetic Poly (epsilon-caprolactone) (PCL) and natural chitosan polymers to develop three dimensional (3D) PCL/chitosan core-shell scaffolds for tissue engineering applications. The scaffolds were fabricated with coaxial electrospinning technique and the characterizations of the samples were done by thickness and contact angle (CA) measurements, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-Ray Photoelectron Spectroscopy (XPS) analyses, mechanical and PBS absorption and shrinkage tests. The average inter-fiber diameter values were calculated for PCL (0.717 +/- 0.001 mu m), chitosan (0.660 +/- 0.007 mu m) and PCL/chitosan core-shell scaffolds (0.412 +/- 0.003 mu m), also the average inter-fiber pore size values exhibited decreases of 66.91% and 61.90% for the PCL and chitosan scaffolds respectively, compared to PCL/chitosan core-shell ones. XPS analysis of the PCL/chitosan core-shell structures exhibited the characteristic peaks of PCL and chitosan polymers. The cell culture studies (MTT assay, Confocal Laser Scanning Microscope (CLSM) and SEM analyses) carried out with L929 ATCC CCL-1 mouse fibroblast cell line proved that the biocompatibility performance of the scaffolds. The obtained results showed that the created micro/nano fibrous structure of the PCL/chitosan core-shell scaffolds in this study increased the cell viability and proliferation on/within scaffolds. (C) 2016 Elsevier B.V. All rights reserved.
