60 results
Search Results
Now showing 1 - 10 of 60
Article Citation - WoS: 56Citation - Scopus: 64Development of 500 W Pem Fuel Cell Stack for Portable Power Generators(Pergamon-elsevier Science Ltd, 2015) Devrim, Yilser; Devrim, Huseyin; Eroglu, InciPolymer Electrolyte Membrane Fuel Cell (PEMFC) portable power generators are gaining importance in emergency applications. In this study, an air-cooled PEMFC stack was designed and fabricated for net 500 W power output. Gas Diffusion Electrodes (GDE's) were manufactured by ultrasonic spray coating technique. Stack design was based on electrochemical data obtained at 0.60 V was 0.5 A/cm(2) from performance tests of a single cell having the same membrane electrode assemblies (MEA) that had an active area of 100 cm(2). Graphite bipolar plates were designed and machined by serpentines type flow. The stack comprising of 24 cells was assembled with external fixing plates. The stack temperature was effectively regulated by the cooling fan based on on-off control system. A maximum power of 647 W was obtained from the stack. The PEMFC stack was stable during start-up and shutdown cycling testing for 7 days at 65 degrees C in H-2/air at a constant cell voltage. Copyright (c) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 86Citation - Scopus: 95Enhancement of Pem Fuel Cell Performance at Higher Temperatures and Lower Humidities by High Performance Membrane Electrode Assembly Based on Nafion/Zeolite Membrane(Pergamon-elsevier Science Ltd, 2015) Devrim, Yilser; Albostan, AyhanThis work reports the preparation of Nafion/zeolite composite membranes with different zeolite loading. The structure of the Nafion/zeolite composite membranes are investigated by Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD) and by thermogravimetric analysis (TGA). The introduction of zeolite particles into the Nafion matrix helps to improve the water uptake, proton conductivity and thermal stability of the nanocomposite membranes compared to the virgin Nafion membrane. The SEM analyses have proved the uniform and homogeneous distribution of zeolite in composite membranes. The composite membranes are tested in a single PEMFC with a 5 cm(2) active area operating at the temperature range of 75-120 degrees C and in humidified under 50% relative humidity (RH) and fully humidified conditions. Single PEMFC tests show that Nafion/zeolite composite membrane is more stable and also performed better than virgin Nafion membrane at low humidity condition. The results indicate the Nafion/zeolite composite membranes could be utilized as the proton exchange membranes for PEMFC. Copyright (C) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 76Citation - Scopus: 76Composite Membrane by Incorporating Sulfonated Graphene Oxide in Polybenzimidazole for High Temperature Proton Exchange Membrane Fuel Cells(Pergamon-elsevier Science Ltd, 2022) Devrim, Yilser; Durmus, Gizem Nur BulanikThe objective of this work is to examine the polybenzimidazole (PBI)/sulfonated graphene oxide (sGO) membranes as alternative materials for high-temperature proton exchange membrane fuel cell (HT-PEMFC). PBI/sGO composite membranes were characterized by TGA, FTIR, SEM analysis, acid doping&acid leaching tests, mechanical analysis, and proton conductivity measurements. The proton conductivity of composite membranes was considerably enhanced by the existence of sGO filler. The enhancement of these properties is related to the increased content of -SO3H groups in the PBI/sGO composite membrane, increasing the channel availability required for the proton transport. The PBI/sGO membranes were tested in a single HT-PEMFC to evaluate high-temperature fuel cell performance. Amongst the PBI/sGO composite membranes, the membrane containing 5 wt. % GO (PBI/sGO-2) showed the highest HT-PEMFC performance. The maximum power density of 364 mW/cm(2) was yielded by PBI/sGO-2 membrane when operating the cell at 160 degrees C under non humidified conditions. In comparison, a maximum power density of 235 mW/cm(2) was determined by the PBI membrane under the same operating conditions. To investigate the HT-PEMFC stability, long-term stability tests were performed in comparison with the PBI membrane. After a long-term performance test for 200 h, the HT-PEMFC performance loss was obtained as 9% and 13% for PBI/sGO-2 and PBI membranes, respectively. The improved HT-PEMFC performance of PBI/sGO composite membranes suggests that PBI/sGO composites are feasible candidates for HT-PEMFC applications. (C) 2022 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 19Citation - Scopus: 21Development of Effective Bimetallic Catalyst for High-Temperature Pem Fuel Cell To Improve Co Tolerance(Wiley, 2021) Al-Tememy, Mogdam Gassy Hussein; Devrim, YilserIn this study, it is aimed to examine the effect of multi-walled carbon nanotube doped graphene nanoplatelet (MWCNT-GNP) supported PtPd bimetallic catalyst on the performance of the high-temperature proton-exchange membrane fuel cell (HT-PEMFC). In addition, PtPd/GNP and PtPd/MWCNT bimetallic catalysts were also investigated for performance comparison. The characterizations of these catalysts were examined by ICP-MS, XRD, HR-TEM, and TGA analysis. The electrochemical characterizations of the catalysts were performed for both cyclic voltammetry (CV) and CO stripping experiments, as well as HT-PEMFC tests. The specific surface area (SSA) for PtPd/GNP and PtPd/MWCNT catalysts was obtained as 148 and 137 m(2)/g, respectively, while the highest SSA was achieved as 164 m(2)/g for PtPd/MWCNT-GNP. The performance of the catalysts was confirmed with the HT-PEMFC tests, based on the H-2/air and reformate gas/air experiments. The electrocatalytic results display that PdPt bimetallic catalysts exhibited higher catalytic property than that of commercial Pt/C catalyst. The highest performance was achieved with PtPd/MWCNT-GNP catalyst as 0.390 and 0.310 W/cm(2)at 160 degrees C for H-2/air and reformat/air, respectively. The obtained results indicate that the PtPd/MWCNT-GNP catalyst is appropriate for HT-PEMFC operations.Conference Object Optimization of modeling parameters of of a direct dimethyl ether fuel cell (DDMEFC)(Ieee, 2019) Alpaydin, Guvenc Umur; Colpan, C. Ozgur; Devrim, YilserDirect alcohol fuel cells are one of the suitable candidates for sustainable power generation in portable applications. Among the different alcohol types that can be used in these fuel cells, DME, which is almost non-toxic at room temperature and easy to liquefy, and has a molecular structure similar to methanol, is one of the suitable options. For this reason, many studies have been carried out to develop direct dimethyl ether fuel cell (DDMEFC). Mathematical modeling studies also play an important role in the development of DDMEFC since they enable the understanding of the performance of the fuel cells more thoroughly. In this study, a model has been developed by using the principles of conservation chemical species and electrochemistry. A modeling study was performed using MATLAB. The values of some modeling parameters were estimated using the genetic algorithm optimization technique.Conference Object Citation - WoS: 98Citation - Scopus: 102Experimental Investigation of Co Tolerance in High Temperature Pem Fuel Cells(Pergamon-elsevier Science Ltd, 2018) Devrim, Yilser; Albostan, Ayhan; Devrim, HuseyinIn the present work, the effect of operating a high temperature proton exchange membrane fuel cell (HT-PEMFC) with different reactant gases has been investigated throughout performance tests. Also, the effects of temperature on the performance of a HT-PEMFC were analyzed at varying temperatures, ranging from 140 degrees C to 200 degrees C. Increasing the operating temperature of the cell increases the performance of the HT-PEMFC. The optimum operating temperature was determined to be 160 degrees C due to the deformations occurring in the cell components at high working temperatures. To investigate the effects of CO on the performance of HT-PEMFC, the CO concentration ranged from 1 to 5 vol %. The current density at 0.6 V decreases from 0.33 A/cm(2) for H-2 to 0.31 A/cm(2) for H-2 containing 1 vol % CO, to 0.29 A/cm(2) for 3 vol % CO, and 0.25 A/cm(2) for 5 vol % CO, respectively. The experimental results show that the presence of 25 vol % CO2 or N-2 has only a dilution effect and therefore, there is a minor impact on the HT-PEMFC performance. However, the addition of CO to H-2/N-2 or H-2/CO2 mixtures increased the performance loss. After longterm performance test for 500 h, the observed voltage drop at constant current density was obtained as similar to 14.8% for H-2/CO2/CO (75/22/3) mixture. The overall results suggest that the anode side gas mixture with up to 5 vol % CO can be supplied to the HT-PEMFC stack directly from the reformer. (C) 2018 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 30Citation - Scopus: 34Investigation of the effect of graphitized carbon nanotube catalyst support for high temperature PEM fuel cells(Pergamon-elsevier Science Ltd, 2020) Devrim, Yilser; Arica, Elif DamlaIn this study, it is aimed to investigate the graphitization effect on the performance of the multi walled carbon nanotube catalyst support for high temperature proton exchange membrane fuel cell (HT-PEMFC) application. Microwave synthesis method was selected to load Pt nanoparticles on both CNT materials. Prepared catalyst was analyzed thermal analysis (TGA), Transmission Electron Microscopy (TEM) and corrosion tests. TEM analysis proved that a distribution of Pt nanoparticles with a size range of 2.8-3.1 nm was loaded on the Pt/CNT and Pt/GCNT catalysts. Gas diffusion electrodes (GDE) were manufactured by an ultrasonic spray method with synthesized catalyst. Polybenzimidazole (PBI) membrane based Membrane Electrode Assembly (MEA) was prepared for observe the performance of the prepared catalysts. The synthesized catalysts were also tested in a HT-PEMFC environment with a 5 cm(2) active area at 160 degrees C without humidification. This study demonstrates the feasibility of using the microwave synthesis method as a fast and effective method for preparing high performance Pt/CNT and Pt/GCNT catalyst for HT-PEMFC. The HT-PEMFC performance evaluation shows current densities of 0.36 A/cm(2)0.30 A/cm(2) and 0.20 A/cm(2) for the MEAs prepared with Pt/GCNT, Pt/CNT and Pt/C catalysts @ 0.6 V operating voltage, respectively. AST (Accelerated Stress Test) analyzes of MEAs prepared with Pt/GCNT and Pt/CNT catalysts were also performed and compared with Pt/C catalyst. According to current density @ 0.6 V after 10,000 potential cycles, Pt/GCNT, Pt/CNT and Pt/C catalysts can retain 61%, 67% and 60% of their performance, respectively. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 28Citation - Scopus: 35Enhancement of Direct Methanol Fuel Cell Performance Through the Inclusion of Zirconium Phosphate(Pergamon-elsevier Science Ltd, 2017) Ozden, Adnan; Ercelik, Mustafa; Ozdemir, Yagmur; Devrim, Yilser; Colpan, C. OzgurNafion/zirconium hydrogen phosphate (ZrP) composite membranes containing 2.5 wt.% ZrP (NZ-2.5) or 5 wt.% ZrP (NZ-5) were prepared to improve the performance of a direct methanol fuel cell (DMFC). The influence of ZrP content on the Nafion matrix is assessed through characterization techniques, such as Thermogravimetric Analysis (TGA), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectroscopy (EIS), and water uptake measurement. Performance testings of the DMFCs based on these composite membranes as well as commercial Nafion (R) 115 membrane were performed using a computer aided fuel cell test station for different values of cell temperature (40 degrees C, 60 degrees C, 80 degrees C, and 100 degrees C) and methanol concentration (0.75 M, 1.00 M, and 1.50 M). Characterization studies indicated that incorporation of ZrP into polymer matrix enhanced the water uptake and proton conductivity values of Nafion membrane. The results of the performance tests showed that the Membrane Electrode Assembly (MEA) having NZ-2.5 provided the highest performance with the peak power density of 551.52 W/m(2) at 100 degrees C and 1.00 M. Then, the performances of the MEAs having the same NZ-2.5 membrane but different cathode catalysts were investigated by fabricating two different MEAs using cathode catalysts made of Pt/C-ZrP and Pt/C (HiSPEC (R) 9100). According to the results of these experiments, the MEA having NZ-2.5 membrane and Pt/C (HiSPEC (R) 9100) cathode catalyst containing 10 wt.% of ZrP exhibited the highest performance with the peak power density of 620.88 W/m(2) at 100 degrees C and 1.00 M. In addition, short-term stability tests were conducted for all the MEAs. The results of the stability tests revealed that introduction of ZrP to commercial (HiSPEC (R) 9100) cathode catalyst improves its stability characteristics. (C) 2017 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 21Citation - Scopus: 21Investigation of Hydrogen Production From Sodium Borohydride by Carbon Nano Tube-Graphene Supported Pdru Bimetallic Catalyst for Pem Fuel Cell Application(Wiley, 2022) Al-Msrhad, Tuqa Majeed Hameed; Devrim, Yilser; Uzundurukan, Arife; Budak, YagmurIn this study, hydrogen (H-2) generation from the hydrolysis of sodium borohydride (NaBH4) catalyzed by bimetallic Palladium-Ruthenium (PdRu) supported on multiwalled carbon nanotube-graphene (MWCNT-GNP) hybrid material is investigated. The effect of various parameters such as temperature, NaBH4 concentration, and catalyst loading and effect of base concentration are examined to observed optimum operating conditions. Experimental results show that the PdRu/MWCNT-GNP bimetallic catalyst has high catalytic activity on NaBH4 hydrolysis reaction. It has been found that PdRu/MWCNT-GNP catalyst shows low activation energy of 22.33 kJ/mol for hydrolysis reaction of NaBH4. The PdRu/MWCNT-GNP catalyst also exhibits H-2 generation rate of 79.2 mmol/min center dot g(cat) at 45 degrees C. It shows good cycle stability in the catalyst reusability test and retained 89% of its initial catalytic activity after fifth use. The high catalytic activity of the PdRu/MWCNT-GNP catalyst makes it promising in H-2 generation from NaBH4 hydrolysis for commercial proton exchange membrane fuel cell (PEMFC) applications.Article Citation - WoS: 52Citation - Scopus: 60Comparative Study of Pv/Pem Fuel Cell Hybrid Energy System Based on Methanol and Water Electrolysis(Pergamon-elsevier Science Ltd, 2019) Budak, Yagmur; Devrim, YilserIn this study, we investigated the comparative analysis of a solar-fuel cell hybrid system based on water and methanol electrolysis. The proposed system comprises PV, electrolyzer and proton exchange membrane fuel cell (PEMFC). The hybrid system is designed to supply the hydrogen (H-2) needed of the PEMFC system and also to fulfill the H-2 requirement of other applications. The actual data of solar irradiation of Izmir, Turkey are used in the simulation. The methanol and water electrolyzers were designed for 1.2 kW PEMFC H-2 demand which were met a house-hold energy requirement. Analyzes show that the use of the methanol electrolyzer can produce 27% more H-2 than the water electrolyzer. According to the study, it was determined that the methanol-based hybrid system offered a viable option for self-sustaining in household application.
