6 results
Search Results
Now showing 1 - 6 of 6
Conference Object DEVELOPMENT OF BIMETALLIC ELECTROCATALYSTS FOR HIGH-TEMPERATURE ELECTROCHEMICAL HYDROGEN PURIFICATION(International Association for Hydrogen Energy, IAHE, 2022) Bal,İ.B.; Durmuş,G.N.B.; Devrim,Y.In this study, PtRu/GNP, PtIr/GNP, and RuIr/GNP bimetallic catalysts were synthesized by microwave-assisted synthesis method, and their performances on the high-temperature electrochemical hydrogen purification (HT-ECHP) were compared. The structural and electrochemical characteristics of the bimetallic catalysts were examined by the TGA, XRD, XPS, and CV techniques. ECHP Tests were performed with reformate gas mixtures containing hydrogen (H2), carbon monoxide (CO), and carbon dioxide (CO2) at temperatures between 140-180°C. The gas at the exit of the ECHP cell was analyzed with the gas chromatography device (GC), and high H2 purity was achieved. © 2022 Proceedings of WHEC 2022 - 23rd World Hydrogen Energy Conference: Bridging Continents by H2. All rights reserved.Conference Object Citation - WoS: 134Citation - Scopus: 148Polybenzimidazole/Sio2< Hybrid Membranes for High Temperature Proton Exchange Membrane Fuel Cells(Pergamon-elsevier Science Ltd, 2016) Devrim, Yilser; Devrim, Huseyin; Eroglu, InciPolybenzimidazole/Silicon dioxide (PBI/SiO2) hybrid membranes were prepared and characterized as alternative materials for high temperature proton exchange membrane fuel cell (HT-PEMFC). The PBI/SiO2 membranes were cast from a PBI polymer synthesized in the laboratory and contained 5 wt. % SiO2 as inorganic filler. Scanning electron microscopy (SEM) analysis showed that the uniform and homogeneous distribution of SiO2 particles in the hybrid membrane. The existence SiO2 has improved the acid retention and proton conductivity properties. A maximum conductivity of 0.1027 S/cm at 180 degrees C was obtained for the PBI/SiO2 hybrid membrane. Gas diffusion electrodes (GDE) were fabricated by ultrasonic coating technique with 1 mg Pt/cm(2) catalyst loading for both anode and cathode. The membranes were tested in a single HT-PEMFC with a 5 cm(2) active area operating at the temperature range of 140 degrees C-180 degrees C. Single HT-PEMFC tests indicated that PBI/SiO2 hybrid membrane was more stable and also performed better than pristine PBI membrane. Maximum current density was observed for PBI/SiO2 membrane at 165 degrees C and cell voltage of 0.6 V as 0.24 A/cm(2). The results suggested that PBI/SiO2 hybrid membrane is promising electrolytes for HT-PEMFC with improved fuel cell performance. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 68Citation - Scopus: 69Composite Membrane by Incorporating Sulfonated Graphene Oxide in Polybenzimidazole for High Temperature Proton Exchange Membrane Fuel Cells(Pergamon-elsevier Science Ltd, 2022) Devrim, Yilser; Durmus, Gizem Nur BulanikThe objective of this work is to examine the polybenzimidazole (PBI)/sulfonated graphene oxide (sGO) membranes as alternative materials for high-temperature proton exchange membrane fuel cell (HT-PEMFC). PBI/sGO composite membranes were characterized by TGA, FTIR, SEM analysis, acid doping&acid leaching tests, mechanical analysis, and proton conductivity measurements. The proton conductivity of composite membranes was considerably enhanced by the existence of sGO filler. The enhancement of these properties is related to the increased content of -SO3H groups in the PBI/sGO composite membrane, increasing the channel availability required for the proton transport. The PBI/sGO membranes were tested in a single HT-PEMFC to evaluate high-temperature fuel cell performance. Amongst the PBI/sGO composite membranes, the membrane containing 5 wt. % GO (PBI/sGO-2) showed the highest HT-PEMFC performance. The maximum power density of 364 mW/cm(2) was yielded by PBI/sGO-2 membrane when operating the cell at 160 degrees C under non humidified conditions. In comparison, a maximum power density of 235 mW/cm(2) was determined by the PBI membrane under the same operating conditions. To investigate the HT-PEMFC stability, long-term stability tests were performed in comparison with the PBI membrane. After a long-term performance test for 200 h, the HT-PEMFC performance loss was obtained as 9% and 13% for PBI/sGO-2 and PBI membranes, respectively. The improved HT-PEMFC performance of PBI/sGO composite membranes suggests that PBI/sGO composites are feasible candidates for HT-PEMFC applications. (C) 2022 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 82Citation - Scopus: 92Graphene Based Catalyst Supports for High Temperature Pem Fuel Cell Application(Pergamon-elsevier Science Ltd, 2018) Devrim, Yilser; Arica, Elif Damla; Albostan, AyhanIn this study, the effect of graphene nanoplatelet (GNP) and graphene oxide (GO) based carbon supports on polybenzimidazole (PBI) based high temperature proton exchange membrane fuel cells (HT-PEMFCs) performances were investigated. Pt/GNP and Pt/GO catalysts were synthesized by microwave assisted chemical reduction support. X-ray diffraction (XRD), Thermogravimetric analysis (TGA), Brauner, Emmet and Teller (BET) analysis and high resolution transmission electron microscopy (HRTEM) were used to investigate the microstructure and morphology of the as-prepared catalysts. The electrochemical surface area (ESA) was studied by cyclic voltammetry (CV). The results showed deposition of smaller Pt nanoparticles with uniform distribution and higher ECSA for Pt/GNP compared to Pt/GO. The Pt/GNP and Pt/GO catalysts were tested in 25 cm(2) active area single HT-PEMFC with H-2/air at 160 degrees C without humidification. Performance evaluation in HT-PEMFC shows current densities of 0.28, 0.17 and 0.22 A/cm(2) for the Pt/GNP, Pt/C and Pt/GO catalysts based MEAs at 160 degrees C, respectively. The maximum power density was obtained for MEA prepared by Pt/GNP catalyst with H-2/Air dry reactant gases as 0.34, 0.40 and 0.46 W/cm(2) at 160 degrees C, 175 degrees C and 190 degrees C, respectively. Graphene based catalyst supports exhibits an enhanced HT-PEMFC performance in both low and high current density regions. The results indicate the graphene catalyst support could be utilized as the catalyst support for HT-PEMFC application. (C) 2018 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 30Citation - Scopus: 34Investigation of the effect of graphitized carbon nanotube catalyst support for high temperature PEM fuel cells(Pergamon-elsevier Science Ltd, 2020) Devrim, Yilser; Arica, Elif DamlaIn this study, it is aimed to investigate the graphitization effect on the performance of the multi walled carbon nanotube catalyst support for high temperature proton exchange membrane fuel cell (HT-PEMFC) application. Microwave synthesis method was selected to load Pt nanoparticles on both CNT materials. Prepared catalyst was analyzed thermal analysis (TGA), Transmission Electron Microscopy (TEM) and corrosion tests. TEM analysis proved that a distribution of Pt nanoparticles with a size range of 2.8-3.1 nm was loaded on the Pt/CNT and Pt/GCNT catalysts. Gas diffusion electrodes (GDE) were manufactured by an ultrasonic spray method with synthesized catalyst. Polybenzimidazole (PBI) membrane based Membrane Electrode Assembly (MEA) was prepared for observe the performance of the prepared catalysts. The synthesized catalysts were also tested in a HT-PEMFC environment with a 5 cm(2) active area at 160 degrees C without humidification. This study demonstrates the feasibility of using the microwave synthesis method as a fast and effective method for preparing high performance Pt/CNT and Pt/GCNT catalyst for HT-PEMFC. The HT-PEMFC performance evaluation shows current densities of 0.36 A/cm(2)0.30 A/cm(2) and 0.20 A/cm(2) for the MEAs prepared with Pt/GCNT, Pt/CNT and Pt/C catalysts @ 0.6 V operating voltage, respectively. AST (Accelerated Stress Test) analyzes of MEAs prepared with Pt/GCNT and Pt/CNT catalysts were also performed and compared with Pt/C catalyst. According to current density @ 0.6 V after 10,000 potential cycles, Pt/GCNT, Pt/CNT and Pt/C catalysts can retain 61%, 67% and 60% of their performance, respectively. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 52Citation - Scopus: 61Multi-Walled Carbon Nanotubes Decorated by Platinum Catalyst for High Temperature Pem Fuel Cell(Pergamon-elsevier Science Ltd, 2019) Devrim, Yilser; Arica, Elif DamlaIn the literature, studies on platinum catalysts deposited on multi-walled carbon nanotube (Pt/MWCNT) have been mostly focused on low temperature fuel cell (LT-PEMFC) applications. In this study, we focus the synthesis and characterization of high temperature fuel cell (HT-PEMFC) performance of Pt/MWCNT in short and long term. The structural properties of the Pt/MWCNT electrocatalyst were analyzed by XRD, TGA, SEM and TEM measurements. The Pt/MWCNTs were also characterized by electrochemical measurements for durability estimation. Laboratory scale MEA with Pt/MWCNT was prepared by ultrasonic coating technique and has been tested in situ in single HT-PEMFC. Performance curves in dry Hydrogen/Air system were obtained that demonstrated performance comparable to commercial catalysts in that HT-PEMFC. The characterizations specified that the electrocatalytic and HT-PEMFC performance of the Pt/MWCNT catalysts are higher power density (0.360 W/cm(2)) than Pt/C (0.310 W/cm(2)) at 160 degrees C. The results obtained show that the synthesized catalysts are suitable for high temperature applications. In addition, the stability studies of MEAs prepared with Pt/MWCNT catalyst were performed by AST tests and compared with Pt/C based MEA. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
