14 results
Search Results
Now showing 1 - 10 of 14
Article Citation - WoS: 9Citation - Scopus: 10Characterization of Properties of Vanadium, Boron and Strontium Addition on Hpdc of A360 Alloy(Elsevier Science Sa, 2021) Gursoy, Ozen; Colak, Murat; Tur, Kazim; Dispinar, DeryaThe demand for lighter weight decreased thickness and higher strength has become the focal point in the automotive industry. In order to meet such requirements, the addition of several alloying elements has been started to be investigated. In this work, the additions of V, B, and Sr on feedability and tensile properties of A360 has been studied. A mold design that consisted of test bars has been produced. Initially, a simulation was carried out to optimize the runners, filling, and solidification parameters. Following the tests, it was found that V addition revealed the highest UTS but low elongation at fracture, while B addition exhibited visa verse. On the other hand, impact energy was higher with B additions.Article Citation - WoS: 9Citation - Scopus: 9Experimental and Theoretical Investigation of the Mechanical Characteristics of Sillenite Compound: Bi12geo20<(Elsevier Science Sa, 2021) Surucu, Gokhan; Isik, Mehmet; Gencer, Aysenur; Gasanly, NizamiThe present study reports the mechanical and elastic characteristics of Bi12GeO20 (BGO) compound by experimental nanoindentation measurements and density functional theory (DFT) calculations. X-ray diffraction pattern of BGO was plotted and revealed diffraction peaks were associated with Miller indices of cubic crystalline structure with lattice constant of a = 10.304 angstrom. Two- and three-dimensional representations of Young's modulus, linear compressibility, shear modulus and Poisson's ratio were presented according to DFT calculations. The calculated elastic constants pointed out the mechanically stable and anisotropic behavior of the BGO. The hardness and Young's modulus ranges of the BGO calculated from DFT studies were found as 3.7-6.3 GPa and 61.7-98.9 GPa, respectively. Hardness and Young's modulus of BGO single crystal were also obtained by analyzing force-dependent nanoindentation experimental data. It was observed that hardness and Young's modulus decrease with increase of load in the low applied loads and then reaches saturation in the high applied loads. This behavior is known as indentation size effect. True hardness value was determined from proportional specimen resistance model as 4.1 GPa. The force independent region presented the Young's modulus as 114 GPa. (C) 2021 Elsevier B.V. All rights reserved.Article Citation - WoS: 63Citation - Scopus: 70Processing and Properties of Boron Carbide (b4c) Reinforced Ldpe Composites for Radiation Shielding(Elsevier Sci Ltd, 2020) Avcioglu, Suna; Buldu, Merve; Kaya, Figen; Ustundag, Cem Bulent; Kam, Erol; Menceloglu, Yusuf Ziya; Kaya, CengizIn the present work, boron carbide (B4C) particles were synthesized with sol-gel technique following with heat treatment at 1500 degrees C in an argon atmosphere. 3-(Triethoxysilyl)-propylamine, a silane coupling agent, was doped on to the surface of synthesized B4C particles. The surface modified B4C particles were embedded in LDPE matrix in order to obtain flexible, lightweight and environmentally friendly shielding materials. The effect of surface functionalization and concentration of boron carbide on its distribution characteristics in the polymer matrix and its effects on the mechanical and neutron shielding properties of the composites are examined. The results showed that high purity-fully crystalline B4C powders with polyhedral-equiaxed morphology in the size range of 20 nm-500 nm were produced. It was found that even the very low amount (0.6-1.7 wt%) of incorporated nano/sub-micron B4C particles in LDPE matrix improved the neutron shielding (up to 39%), tensile strength (9.3%) and impact resistance (8%) of the composites.Article Citation - WoS: 10Citation - Scopus: 10Determination of Mechanical Properties of Bi12tio20< Crystals by Nanoindentation(Elsevier Sci Ltd, 2022) Isik, M.; Gasanly, N. M.; Rustamov, F. A.Bi12TiO20 (BTO) single crystal was grown by Czochralski method and investigated mechanically by nano-indentation measurements. X-ray diffraction pattern of the crystal presented one intensive peak around 37.95 degrees associated with (330) plane of cubic crystalline structure. Nanoindentation experiments were performed at various loads between 5 and 100 mN. Hardness and Young's modulus of the crystal were determined by Oliver-Pharr method. The hardness-load dependency exhibited behavior of indentation size effect. True hardness value of BTO crystal was revealed as 4.4 GPa. Young's modulus decreased with increase of load and load-independent Young's modulus was found around 93 GPa at high loads. The load-dependent elastic and plastic deformation components were calculated and it was observed that the dominant component in BTO single crystal is plastic deformation at the applied loads. The present paper reports for the first time the mechanical characteristics of the BTO single crystal by carrying out nanoindentation experiments.Article Citation - WoS: 35Citation - Scopus: 35Friction Stir Processing of Dual Phase Steel: Microstructural Evolution and Mechanical Properties(Elsevier Science inc, 2019) Aktarer, S. M.; Kucukomeroglu, T.; Davut, K.The influence of friction stir processing (FSP) on the microstructure and mechanical properties of a DP 600 steel has been studied. The microstructure evolution during the FSP has been characterized using electron back scatter diffraction (EBSD) technique and scanning and transmission electron microscopes. Standard tension and hardness tests were used to characterize the mechanical properties. The results show that the FSP produced a refined microstructure composed of ferrite, bainite, martensite, and tempered martensite which in turn increased the hardness and strength magnitudes by a factor of 1.5. The initially 2.83 mu m average grain size of ferrite has decreased to 0.79 mu m in the pin effected zone of (PE-SZ-I) of the processed region. Both EBSD and TEM observations showed regions with high dislocation density and sub-structures region in the processed zone. The grain size became coarser, the density of both dislocations and low-angle grain boundaries decrease, away from the processed zone. Moreover, phase fractions and hardness values were predicted using CALPHAD thermodynamic based software based on commercial material properties. Although the prediction does not take into consideration the influence of severe plastic deformation, the results were within 10% uncertainties of the experimental findings. The present study demonstrates that an ultra-fine grained structure can be obtained through the thickness of a 1.5 mm thick D P600 steel sheet via FSP. FSP can produce a range of different hardness and strength values; which can also be predicted successfully by inputting the composition and local temperatures reached during the FSP.Article Citation - WoS: 34Citation - Scopus: 37Characterization of Gas Tunnel Type Plasma Sprayed Hydroxyapatite-Nanostructure Titania Composite Coatings(Elsevier, 2015) Yugeswaran, S.; Kobayashi, A.; Ucisik, A. Hikmet; Subramanian, B.Hydroxyapatite (HA) can be coated onto metal implants as a ceramic biocompatible coating to bridge the growth between implants and human tissue. Meanwhile many efforts have been made to improve the mechanical properties of the HA coatings without affecting its bioactivity. In the present study, nanostructure titania (TiO2) was mixed with HA powder and HA-nanostructure TiO2 composite coatings were produced by gas tunnel type plasma spraying torch under optimized spraying conditions. For this purpose, composition of 10 wt% TiO2 + 90 wt% HA, 20 wt% TiO2 + 80 wt% HA and 30 wt% TiO2 + 70 wt% HA were selected as the feedstock materials. The phase, microstructure and mechanical properties of the coatings were characterized. The obtained results validated that the increase in weight percentage of nanostructure TiO2 in HA coating significantly increased the microhardness, adhesive strength and wear resistance of the coatings. Analysis of the in vitro bioactivity and cytocompatibility of the coatings were done using conventional simulated body fluid (c-SBF) solution and cultured green fluorescent protein (GFP) labeled marrow stromal cells (MSCs) respectively. The bioactivity results revealed that the composite coating has bio-active surface with good cytocompatibility. (C) 2015 Elsevier B.V. All rights reserved.Article Citation - WoS: 6Citation - Scopus: 6Effect of Martensite Volume Fraction on Mechanical Properties of Dual-Phase Treated Aisi-4012 Sheet Steels(Carl Hanser verlag, 2010) Aksakal, B.; Karaca, F.; Arikan, R.Hot rolled AISI-4012 sheet steels have been heat treated to obtain a ductile dual phase microstructure. The specimens were heat treated in the ferrite (a) and austenite (7) phase region at temperatures of 740, 760, 790 and 820 degrees C and corresponding time intervals of 15, 30, 60 and 90 min and then quenched into water. Hardness measurements, tensile, bending, and impact tests were performed in order to determine the mechanical properties of the dual phase steel. These were examined with respect to the martensite volume fraction. Both the flow and tensile stresses increased whereas elongation decreased with increasing dual phase treatment temperature and martensite volume fraction. The optimum mechanical properties and the appropriate dual-phase microstructure are achieved at 740 and 760 degrees C annealing with subsequent water quenching. From examinations it was deduced that ductile fracture occurred in the tested samples.Article Citation - WoS: 41Citation - Scopus: 44Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier Science Sa, 2022) Ozer, Seren; Bilgin, Guney Mert; Davut, Kemal; Esen, Ziya; Dericioglu, Arcan F.The effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples dis-appeared and converted into a mixture of columnar and equiaxed grains. Nano-sized gamma '' and/or gamma' precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 degrees C for 8 h) tested at 600 degrees C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700-800 degrees C, which was attributed to intermediate temperature embrittlement.Article Citation - WoS: 24Citation - Scopus: 24Anisotropic mechanical properties of Tl4Ag18Te11 compound with low thermal conductivity(Academic Press inc Elsevier Science, 2020) Gencer, Aysenur; Surucu, Ozge; Surucu, Gokhan; Deligoz, EnginThe anisotropic mechanical properties of Tl4Ag18Te11 compound was investigated elaborately for the first time by using Density Functional Theory calculations with the Vienna Ab-initio Simulation Package in this work. Tl4Ag18Te11 compound was optimized in the I4mm space group and the formation energy was determined as a negative value that is the indication of the experimental synthesizability of this compound. The optimized crystal structure was employed for the calculations of the elastic constants and the obtained values revealed the mechanical stability of Tl4Ag18Te11 compound. The polycrystalline properties were determined such as shear modulus, Poisson's ratio, etc. In addition, the anisotropic elastic properties were presented. The direction dependent sound waves velocities, polarization of the sound waves, enhancement factor and the power flow angle were determined. The thermal conductivity studies were performed and the minimum thermal conductivity (0.259 W m(-1)K(-1)) and the diffusion thermal conductivity (0.202 W m(-1)K(-1)) were calculated. This study illustrates the capability of this compound for the thermoelectric materials.Article Citation - WoS: 22Citation - Scopus: 24Mechanical and Biological Properties of Al2o3< and Tio2 Co-Doped Zirconia Ceramics(Elsevier Sci Ltd, 2017) Agac, Ozlem; Gozutok, Melike; Sasmazel, Hilal Turkoglu; Ozturk, Abdullah; Park, JongeeVarious amounts (ranging from 0 to 2 wt%) of TiO2 and Al2O3 were mono and co-doped to tetragonal zirconia ceramic containing 3 mol% yttria (3Y-TZP) by mechanical ball milling. Powders were compacted by uniaxial pressing at a pressure of 23 MPa. The compacts were pressureless sintered at 1450 degrees C for 2 h. Density, hardness, fracture toughness, and cell attachment of the co-doped 3Y-TZP ceramics were measured with respect to dopant addition to determine the effects of the kind and amount of dopants on the properties. The results show that density decreased gradually as the amount of dopant was increased. The mechanical properties showed the maximum value when 0.5 wt% TiO2 and 1.0 wt% Al2O3 were co-doped to 3Y-TZP. Crystalline phase formation and microstructural morphology were investigated by XRD and SEM analyses to explain the variations in the properties. Co-doping of TiO2 and Al2O3 to 3Y-TZP did not have an influence on the phases present, but decreased the grain size. The co-doping also affected the cell attachment and the growth on the surface of the zirconia ceramics.
