4 results
Search Results
Now showing 1 - 4 of 4
Article Citation - WoS: 5Citation - Scopus: 7Lessons Learned From Four Recent Turkish Earthquakes: Sivrice-Elazığ, Aegean Sea, and Dual Kahramanmaraş(Springer, 2024) Tunc, Goekhan; Mertol, Halit Cenan; Akis, TolgaT & uuml;rkiye is located in an earthquake-prone region where almost all of its population resides in risky areas. In the past 100 years, there has been a strong earthquake every two years and a major one every 3 years. This study investigates the impact of four recent earthquakes, that occurred between 2020 and 2023, on reinforced concrete (RC) buildings. The first, Sivrice-Elaz & imath;& gbreve;, struck the eastern part of T & uuml;rkiye on January 24, 2020, with a moment magnitude of Mw = 6.8. The second, the Aegean Sea, hit the western part of the country on October 30, 2020, with an Mw of 6.6. The third and fourth are the February 6, 2023 dual Kahramanmara & scedil; earthquakes with Mws of 7.7 and 7.6, which struck the eastern part of T & uuml;rkiye approximately 9 h apart. Immediately following these earthquakes, a technical team investigated each of the damaged areas. This study summarizes their findings on RC buildings. It was discovered that the majority of the collapsed or severely damaged RC buildings were constructed before 2000. The main reasons for this included technological limitations, specifically on producing high-quality concrete, as well as a lack of public policies and enforced laws in the construction sector to maintain an acceptable international standard. Furthermore, the damage patterns of buildings from these four earthquakes indicated poor workmanship, low material quality, improper structural framing, a common appearance of soft and weak stories, the inadequate use of shear walls, and defective reinforcement configuration. The significance of soil studies and the enforcement of building inspections are also discussed, along with the earthquake codes. The study concludes that the maximum peak ground accelerations from the dual Kahramanmara & scedil; earthquakes were almost triple the code-prescribed values. Therefore, it is recommended that the current mapped spectral acceleration values be revised and that buildings constructed before 2000 should be prioritized while determining their structural performances.Article Citation - WoS: 11Citation - Scopus: 13Automated Selection of Optimal Material for Pressurized Multi-Layer Composite Tubes Based on an Evolutionary Approach(Springer London Ltd, 2018) Azad, Saeid Kazemzadeh; Akis, TolgaDecision making on the configuration of material layers as well as thickness of each layer in composite assemblies has long been recognized as an optimization problem. Today, on the one hand, abundance of industrial alloys with different material properties and costs facilitates fabrication of more economical or light weight assemblies. On the other hand, in the design stage, availability of different alternative materials apparently increases the complexity of the design optimization problem and arises the need for efficient optimization techniques. In the present study, the well-known big bang-big crunch optimization algorithm is reformulated for optimum design of internally pressurized tightly fitted multi-layer composite tubes with axially constrained ends. An automated material selection and thickness optimization approach is employed for both weight and cost minimization of one-, two-, and three-layer tubes, and the obtained results are compared. The numerical results indicate the efficiency of the proposed approach in practical optimum design of multi-layer composite tubes under internal pressure and quantify the optimality of different composite assemblies compared to one-layer tubes.Article Citation - WoS: 20Citation - Scopus: 20The Stress Response of Partially Plastic Rotating Fgm Hollow Shafts: Analytical Treatment for Axially Constrained Ends(Taylor & Francis inc, 2006) Eraslan, Ahmet N.; Akis, Tolgaanalytical solutions to estimating the elastoplastic response of rotating functionally graded (FGM) hollow shafts with fixed ends are presented. The modulus of elasticity, as well as the uniaxial yield limit of the shaft material, are assumed to vary nonlinearly in the radial direction. The plastic model is based on Tresca's yield criterion, its associated flow rule, and ideal plastic material behaviour. Elastic, partially plastic, fully plastic, and residual stress states are investigated. It is shown that the elastoplastic stress response of a rotating FGM hollow shaft is affected significantly by the nonhomogeneity of the material. Unlike the case of a homogeneous hollow shaft, plastic deformation may commence at the inner surface, at the outer surface, or simultaneously at both surfaces. Accordingly, each case requires different mathematical treatment to arrive at its partially plastic solution. It is also shown that, by taking a numerical limit, the complete FGM solution presented herein converge to the solution of a homogeneous rotating shaft.Article Citation - WoS: 9Citation - Scopus: 10Influence of Cement Replacement by Calcinated Kaolinitic and Montmorillonite Clays on the Properties of Mortars(Springer Heidelberg, 2023) Al-Noaimat, Yazeed A. A.; Akis, TolgaThis study aims to investigate the decomposition and pozzolanic reactivity of two different clays (kaolinitic and montmorillonite) from different origins and to determine their effects after calcination on the properties of cement mortars when used to replace Portland cement partially. Mineralogical and chemical compositions of the clay samples were determined using XRD (X-ray Diffractometer) and XRF (X-ray Fluorescence) tests, respectively. TG-DTA (Thermogravimetry-Differential Thermal Analyses) was used to determine the temperature profiles and the burning temperatures of the clays. The density and fineness of the burnt clays were also determined. In order to investigate the optimum material properties, different burning temperatures and replacement levels were considered. It was found that for all temperatures, the two burnt clays possess good pozzolanic activity. The highest compressive strength and lowest water absorption capacity were achieved when the clay determined as kaolinitic was burned at 700 & DEG;C and with 10% replacement level. While for the clay determined as montmorillonite, the optimum properties were obtained at 700 & DEG;C with a 20% substitution level. Kaolinite had better pozzolanic reactivity than montmorillonite, achieving higher strength performance with lower water absorption when partially replaced with cement. Moreover, it had compressive strength values even higher than plain cement.
