6 results
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 6Citation - Scopus: 6Electrochemical Copolymerization and Characterization of Dianilines Linked by Polyether Bridge With Aniline(Springer, 2010) Tirkes, Seha; Onal, Ahmet M.Copolymer of aniline and triethylene glycol bis(o-aminophenyl) ether was synthesized by constant potential electrolysis. Cyclic voltammogram of the copolymer films recorded in the monomer-free electrolytic solution revealed that the redox behavior of the films approaches to that of poly(triethylene glycol bis(o-aminophenyl) ether) with increasing amount of triethylene glycol bis(o-aminophenyl) in the feed ratio. Copolymerization was investigated by in situ recording the changes in the electronic absorption spectrum during electrolysis. The free standing copolymer film was characterized utilizing Fourier transform infrared spectrometer, and spectroelectrochemical behavior of the copolymer was investigated via in situ UV-vis spectroscopic technique. Besides the electron spin resonance study of the copolymer film, the different morphologies of the polymers were examined by scanning electron microscopy and the copolymerization was confirmed. The temperature dependence conductivity of the copolymer film was measured by four-probe technique in the temperature range of 100-300 K, and the calculated parameters showed that conduction mechanism fits to variable range hopping.Article Citation - WoS: 64Citation - Scopus: 74Production and Characterization of Poly (lactic Acid)-Based Biocomposites Filled With Basalt Fiber and Flax Fiber Hybrid(Sage Publications Ltd, 2020) Eselini, Najah; Tirkes, Seha; Akar, Alinda Oyku; Tayfun, UmitPoly (lactic acid) (PLA)-based biocomposites containing flax fiber (FF) and basalt fiber (BF) both separately and together were prepared by melt blending method at the total constant ratio of 30 wt%. Mechanical properties, thermo-mechanical characteristics, thermal stability, flow behaviors, water uptake, and morphology of composites were investigated by tensile, hardness and impact tests, dynamic mechanical analysis (DMA), thermal gravimetric analysis, melt flow index (MFI) test, water absorption, and scanning electron microscopy, respectively. Mechanical test results show that tensile strength, elongation, elastic modulus, and impact strength are extended up to higher values with increase in BF content in hybrid composites. Conversely, the presence of FF displays a negative effect in which these values drop down drastically as the FF concentration increases. On the other hand, slightly higher hardness values are obtained by the addition of FF at higher loadings. DMA analysis reveals that BF inclusion leads glass transition temperature of PLA to one point higher, but hybrid and FF containing composites shift that temperature to lower values. Storage moduli of composites are enhanced with the increase in BF concentration and remarkable decreases are observed for FF-filled composites. Hybrid composites exhibit average MFI values between PLA/FF and PLA/BF composites.Article Citation - WoS: 10Citation - Scopus: 10Synthesis and Characterization of Novel High Temperature Structural Adhesives Based on Nadic End Capped Mda-Btda Copolyimide(Iop Publishing Ltd, 2018) Acar, Oktay; Varis, Serhat; Isik, Tugba; Tirkes, Seha; Demir, Mustafa M.A series of novel copolyimide structural adhesives were synthesized using 4,4'-diaminodiphenyl-methane (MDA), 3,4'-oxydianiline (ODA) and 3,3',4,4'-benzophenonetetracarboxylic acid dianhy-dride (BTDA) as co-monomers, and nadic anhydride as an end cap reagent. The adhesives with different MDA and ODA contents were examined in terms of their structure, thermal stability, mechanical properties, and adhesive performance. They have glass transition temperatures (T-g) about 400 degrees C, with thermal stability up to 500 degrees C. The effect of diamine monomer compositions on adhesion performance and processability of the copolyimides were studied. The copolyimides exhibited adhesion strength up to 16.3 MPa at room temperature. Nadic end capped MDA-BTDA-ODA copolyimide resins gained adjustable and controllable processability with the addition of ether bridged aromatic segments. The copolyimide adhesive with equimolar composition of MDA: ODA is distinguished form the both commercial PMR-15 and LARC RP-46 polyimides in terms of its better processability and mechanical performance.Article Citation - WoS: 31Citation - Scopus: 34Mechanical, Thermo-Mechanical and Morphological Characterization of Abs Based Composites Loaded With Perlite Mineral(Iop Publishing Ltd, 2020) Alghadi, Aiah Mohamed; Tirkes, Seha; Tayfun, UmitAcrylonitrile-butadiene-styrene (ABS) copolymer was filled with perlite mineral (PER) at four different loading level of 2.5%, 5%, 10% and 15%. ABS/PER composites were produced using lab-scale micro-compounder followed by injection molding process. Mechanical, thermo-mechanical, melt-flow and morphological properties of composites were reported by tensile and impact tests, dynamic mechanical analysis (DMA), melt flow index (MFI) test and scanning electron microscopy (SEM), respectively. Mechanical characterizations revealed that tensile strength, elongation and Youngs? modulus of ABS were improved by PER inclusions. However, impact strength of ABS reduced with increase of PER concentration. Glass transition temperature of ABS displayed increasing trend for %5 concentration of PER. MFI test implied that PER addition caused slight decreasing for MFI value of unfilled ABS. Homogeneous dispersion of PER particles into ABS matrix for their lower loading level was obtained from SEM micrographs of composites. According to findings, 5% PER containing sample exhibited the best performance and it was remarked as the most suitable candidate among fabricated ABS based composites.Article Citation - WoS: 14Citation - Scopus: 17Hybrid Nanocomposites of Elastomeric Polyurethane Containing Halloysite Nanotubes and Poss Nanoparticles: Tensile, Hardness, Damping and Abrasion Performance(Cambridge Univ Press, 2020) Mohamed, Salma Taher; Tirkes, Seha; Akar, Alinda Oyku; Tayfun, UmitThermoplastic polyurethane (TPU) matrix was reinforced with polyhedral oligomeric silsesquioxane (POSS) and halloysite nanotubes (HNT), both separately and combined. Composite samples were fabricated using a melt-compounding method. Characterization of the composites obtained was performed via tensile and hardness tests, melt-flow index measurements (MFI), abrasion tests, dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) to investigate the mechanical performance, flow behaviour, tribological characteristics, thermo-mechanical response and morphological properties. The greatest tensile strength value was obtained for the smallest HNT content. Further addition of HNT resulted in agglomerations for both POSS and HNT particles. The shore hardness of TPU was enhanced by filler inclusions. The TPU/POSS composites displayed significant improvement in terms of abrasion resistance compared to TPU at lower loading levels. The DMA study showed that composites containing 0.5% POSS and 1.0% HNT displayed the greatest storage modulus. The glass-transition temperature of TPU shifted to smaller values with the addition of both nanoparticles. The HNT inclusions increased the MFI value of TPU because of their large aspect ratio. Homogeneous mixing of nanoparticles in the TPU matrix was confirmed by a SEM study of the composites. Their dispersion decreased as the concentrations of POSS and HNT increased. An adjuvant effect of POSS with HNT was achieved in their hybrid composites.Article Citation - WoS: 13Citation - Scopus: 15Atomistic Engineering of Chemiluminogens: Synthesis, Properties and Polymerization of 2,3-Dihydro Scaffolds(Springer/plenum Publishers, 2017) Algi, Melek Pamuk; Tirkeş, Seha; Oztas, Zahide; Cihaner, Atilla; Tirkes, Seha; Cihaner, Atilla; Algi, Fatih; Tirkeş, Seha; Cihaner, Atilla; Chemical Engineering; Chemical EngineeringTwo chemiluminescent compounds containing 2,5-di(thien-2-yl)pyrrole and pyridazine units, namely 5,7-di(thiophen-2-yl)-2,3-dihydro-1H-pyrrolo[3,4-d]pyridazine-1,4(6H)-dione (5) and 6-phenyl-5,7-di(thiophen-2-yl)-2,3-dihydro-1H-pyrrolo[3,4-d]pyridazine-1,4(6H)-dione (6), were successfully synthesized and electrochemically polymerized. The compounds have chemiluminescent properties and glow in the presence of hydrogen peroxide in basic medium. The intensity of the glow can be increased dramatically by using Fe3+ ions, hemin (1.0 ppm) or blood samples (1.0 ppm) as catalyst. The compounds 5 and 6 have one well-defined irreversible oxidation peak at 1.08 V and 1.33 V vs Ag/AgCl, respectively. Electrochemical polymerization of both 5 and 6 were carried out successfully by repeating potential scanning in the presence of BF3. Et2O in an electrolyte solution of 0.1 M LiClO4 dissolved in acetonitrile. The electronic band gaps (E-g) of the polymers P5 and P6 were found to be 2.02 eV and 2.16 eV, respectively. On the other hand, the corresponding polymers are electroactive and exhibited electrochromic features.
