7 results
Search Results
Now showing 1 - 7 of 7
Article Citation - WoS: 33Citation - Scopus: 35Exact Solution of Rotating Fgm Shaft Problem in the Elastoplastic State of Stress(Springer, 2007) Akis, Tolga; Eraslan, Ahmet N.Plane strain analytical solutions to estimate purely elastic, partially plastic and fully plastic deformation behavior of rotating functionally graded (FGM) hollow shafts are presented. The modulus of elasticity of the shaft material is assumed to vary nonlinearly in the radial direction. Tresca's yield criterion and its associated flow rule are used to formulate three different plastic regions for an ideal plastic material. By considerina different material compositions as well as a wide range of bore radii, it is demonstrated in this article that both the elastic and the elastoplastic responses of a rotating FGM hollow shaft are affected significantly by the material nonhomogeneity.Article Citation - WoS: 2Citation - Scopus: 2Structural Design Optimization of Multi-Layer Spherical Pressure Vessels: a Metaheuristic Approach(Springer, 2019) Akis, Tolga; Azad, Saeid KazemzadehThis study addresses the optimum design problem of multi-layer spherical pressure vessels based on von Mises yield criterion. In order to compute the structural responses under internal pressure, analytical solutions for one-, two-, and three-layer spherical pressure vessels are provided. A population-based metaheuristic algorithm is reformulated for optimum material selection as well as thickness optimization of multi-layer spherical pressure vessels. Furthermore, in order to enhance the computational efficiency of the optimization algorithm, upper bound strategy is also integrated with the algorithm for reducing the total number of structural response evaluations during the optimization iterations. The performance of the algorithm is investigated through weight and cost minimization of one-, two- and three-layer spherical pressure vessels and the results are presented in detail. The obtained numerical results, based on different internal pressures as well as vessel sizes, indicate the usefulness and efficiency of the employed methodology in optimum design of multi-layer spherical pressure vessels.Article Citation - WoS: 1Citation - Scopus: 3Modeling of Asymmetric Shear Wall-Frame Building Structures(Architectural inst Japan, 2009) Akis, Tolga; Tokdemir, Turgut; Yilmaz, CetinBased on the conventional wide column analogy, two different three-dimensional shear wall models for open and closed sections are proposed. These approximate models are verified in comparison to not only the results available in the literature but also the ones obtained by Using models containing shell elements. With the help of these new models five different groups of shear wall-frame structures with different floor plans and different heights are analyzed. The first three natural vibration periods are determined and time history analyses are performed. The results Of these computations are observed to be in good agreement with those obtained by detailed models containing shell elements.Article Citation - WoS: 1Citation - Scopus: 1Metaheuristic Optimization of Rotating Multilayer Composite Tubes Under Internal Heating and Pressure(Springer, 2022) Azad, Saeid Kazemzadeh; Akis, TolgaAlthough analysis/design of multilayer assemblies has been always an active field of research, works on the optimal design of rotating multilayer composite tubes are very limited. This paper addresses the design optimization of rotating multilayer composite tubes under internal heating and pressure. For determining the structural responses, analytical solutions are provided based on different boundary conditions. The automated selection of optimal material as well as thickness optimization of pressurized multilayer assemblies is carried out under different angular speed and internal heating conditions using a metaheuristic algorithm. The corresponding optimum design for each angular speed as well as internal heating condition is sought, and the numerical results are discussed. The study provides general guidelines for conceptual design of rotating multilayer composite tubes subjected to internal heating and pressure.Article Citation - WoS: 4Citation - Scopus: 6A Study of Shrink-Fitting for Optimal Design of Multi-Layer Composite Tubes Subjected To Internal and External Pressure(Springer, 2019) Azad, Saeid Kazemzadeh; Akis, TolgaThis paper addresses the effect of shrink-fitting on the optimal design of pressurized multi-layer composite tubes. Analytical solutions for structural response calculations are provided for axially constrained two- and three-layer shrink-fitted tubes under both internal and external pressure. A recently developed numerical evolutionary optimization algorithm is employed for weight and cost minimization of these assemblies. In order to investigate the effect of shrink-fitting, first, optimal material selection and thickness optimization of tightly fitted tubes, under either internal or both internal and external pressure, are accomplished without shrink-fitting. Next, under the same loading and boundary conditions the assemblies are optimized where shrink-fitting parameters are taken into account for weight and cost minimization. The numerical results obtained for multi-layer composite tubes with and without shrink-fitting indicate that more economical or lightweight assemblies can be obtained if shrink-fitting parameters are treated as additional design variables of the optimization problem. Furthermore, it is observed that considering the shrink-fitting parameters for optimal design becomes more advantageous in the test cases with a higher ratio of internal pressure to external pressure.Article Citation - WoS: 54Citation - Scopus: 58Investigation of Rc Buildings After 6 February 2023, Kahramanmaras, Turkiye Earthquakes(Mdpi, 2023) Mertol, Halit Cenan; Tunc, Gokhan; Akis, Tolga; Kantekin, Yunus; Aydin, Ishak CanTwo major earthquakes struck Pazarcik and Elbistan, towns in Kahramanmaras, Turkiye, on 6 February 2023, approximately 9 h apart. The first earthquake, recorded at 04:17 local time, had a M-w = 7.7, with a focal depth of 8.6 km. At 13:24 local time, a second earthquake occurred with M-w = 7.6 at a focal depth of 7 km, approximately 90 km north of the first one. A total of 11 provinces were severely affected by these earthquakes. As of 15 April 2023, they caused close to 51,000 deaths and almost 215,000 completely destroyed/severely damaged buildings. At some locations, the largest horizontal peak ground acceleration (PGA) values of the first and second earthquakes exceeded the code-generated PGAs by almost 3 and 1.75 times, respectively. A technical team visited these areas within 15 h of the first earthquake. The purpose of this article is to present their observations, findings, and the characteristics of the two earthquakes, with comprehensive site survey results supported by photographs. This study concludes that most of the collapsed and severely/moderately damaged buildings in the region were built between 1975 and 2000, when site inspections were rare or non-existent. In addition to the high PGAs recorded in these earthquakes, it was verified that the design and construction of these buildings did not fully comply with the earthquake codes valid at the time. The collapsed buildings and their damage patterns confirm inadequate development length, violation of bending stirrup ends at 135 & DEG;, deficiencies in construction materials and reinforcement configuration, noncompliance with confinement zones, violation of the strong beam-stronger column analogy, and issues related to building inspection. Based on the extent of the damage, it is strongly recommended that the structural performance inspection of all other buildings located near major fault lines, specifically those constructed between 1975 and 2000, should be completed. Since these earthquakes generated much higher PGAs, which is believed to be one of the main reasons for the extensive damage, a re-evaluation of all other PGAs along major fault lines is also recommended.Article Citation - WoS: 15Citation - Scopus: 16Damage Observation of Reinforced Concrete Buildings After 2020 Sivrice (elazig) Earthquake, Turkey(Asce-amer Soc Civil Engineers, 2021) Cenan Mertol, Halit; Tunc, Gokhan; Akis, TolgaAn earthquake with a magnitude of M-w = 6.8 and a depth of approximately 8.06 km occurred on January 24, 2020, with the epicenter near the town of Sivrice in Elazig province, Turkey. The earthquake resulted in numerous collapses and severe structural damage to the buildings located in the downtowns and villages of Elazig and Malatya provinces. A technical team investigated the earthquake-affected areas, and this study presents their observations and findings with respect to reinforced concrete buildings. It was concluded that almost all of the collapsed or severely-damaged reinforced concrete buildings were constructed between 1975 and 1998. The design and construction of these buildings did not comply with the specifications of the Turkish earthquake codes valid at that time. The failures and severe damage of the buildings are associated with poor material quality, inadequate reinforcement configuration, and framing problems related to their lateral load-carrying systems. Therefore, it is recommended that buildings constructed between 1975 and 1998 in the region be structurally re-evaluated to avoid additional loss of life and property in future earthquakes. (C) 2021 American Society of Civil Engineers.
