Browsing by Author "Ozdemir, Yagmur"
Now showing 1 - 4 of 4
- Results Per Page
- Sort Options
Article Citation Count: 153Development of polybenzimidazole/graphene oxide composite membranes for high temperature PEM fuel cells(Pergamon-elsevier Science Ltd, 2017) Devrim, Yılser; Pehlivanoglu, Kubra; Ozdemir, Yagmur; Devrim, Yilser; Energy Systems EngineeringIn this study, phosphoric acid doped Polybenzimidazole/Graphene Oxide (PBI/GO) nano composite membranes were prepared by dispersion of various amounts of GO in PBI polymer matrix followed by phosphoric acid doping for high temperature proton exchange membrane fuel cell (HT-PEMFC) application. The structure of the PBI/GO composite membranes was investigated by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and by thermogravimetric analysis (TGA). The introduction of GO into the FBI polymer matrix helps to improve the acid doping, proton conductivity and acid leaching properties. The SEM analyses have proved the uniform and homogeneous distribution of GO in composite membranes. The composite membranes were tested in a single HT-PEMFC with a 5 cm(2) active area at 165 degrees C without humidification. HT-PEMFC tests show that PBI/ GO composite membrane with 2 wt. % GO content performed better than bare PBI membrane at non humidified condition. At ambient pressure and 165 degrees C, the maximum power density of the PBI/GO-1 membrane can reach 0.38 W/cm(2), and the current density at 0.6 V is up to 0.252 A/cm(2), with H-2/air. The results indicate the PBI/GO composite membranes could be utilized as the proton exchange membranes for HT-PEMFC. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Conference Object Citation Count: 25Enhancement of direct methanol fuel cell performance through the inclusion of zirconium phosphate(Pergamon-elsevier Science Ltd, 2017) Devrim, Yılser; Ercelik, Mustafa; Ozdemir, Yagmur; Devrim, Yilser; Colpan, C. Ozgur; Energy Systems EngineeringNafion/zirconium hydrogen phosphate (ZrP) composite membranes containing 2.5 wt.% ZrP (NZ-2.5) or 5 wt.% ZrP (NZ-5) were prepared to improve the performance of a direct methanol fuel cell (DMFC). The influence of ZrP content on the Nafion matrix is assessed through characterization techniques, such as Thermogravimetric Analysis (TGA), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectroscopy (EIS), and water uptake measurement. Performance testings of the DMFCs based on these composite membranes as well as commercial Nafion (R) 115 membrane were performed using a computer aided fuel cell test station for different values of cell temperature (40 degrees C, 60 degrees C, 80 degrees C, and 100 degrees C) and methanol concentration (0.75 M, 1.00 M, and 1.50 M). Characterization studies indicated that incorporation of ZrP into polymer matrix enhanced the water uptake and proton conductivity values of Nafion membrane. The results of the performance tests showed that the Membrane Electrode Assembly (MEA) having NZ-2.5 provided the highest performance with the peak power density of 551.52 W/m(2) at 100 degrees C and 1.00 M. Then, the performances of the MEAs having the same NZ-2.5 membrane but different cathode catalysts were investigated by fabricating two different MEAs using cathode catalysts made of Pt/C-ZrP and Pt/C (HiSPEC (R) 9100). According to the results of these experiments, the MEA having NZ-2.5 membrane and Pt/C (HiSPEC (R) 9100) cathode catalyst containing 10 wt.% of ZrP exhibited the highest performance with the peak power density of 620.88 W/m(2) at 100 degrees C and 1.00 M. In addition, short-term stability tests were conducted for all the MEAs. The results of the stability tests revealed that introduction of ZrP to commercial (HiSPEC (R) 9100) cathode catalyst improves its stability characteristics. (C) 2017 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation Count: 83Fabrication and Characterization of Cross-linked Polybenzimidazole Based Membranes for High Temperature PEM Fuel Cells(Pergamon-elsevier Science Ltd, 2017) Devrim, Yılser; Ozkan, Necati; Devrim, Yilser; Energy Systems EngineeringIn this study different types of crosslinked polybenzimidazole (PBI) membranes were compared as high temperature proton exchange membrane fuel cells (HT-PEMFC). Cross-linking of PBI was performed with different cross-linkers including bisphenol A diglycidyl ether (BADGE), ethylene glycol diglycidyl ether (EGDE), alpha-alpha'-dibromo-p-xylene (DBpX), and terephthalaldehyde (TPA). The crosslinked membranes have been characterized by thermogravimetric analysis, scanning electron microscopy, acid uptake and impedance analyses. The crosslinking of the PBI polymer matrix helps to improve the acid retention properties. PBI/BADGE presented the highest acid retention properties. Proton conductivities of the membranes were comparable to that of commercial membranes. Conductivity values up to 0.151 S.cm(-1) were obtained at 180 degrees C with PBI/DBpX membranes. Gas diffusion electrodes (GDE) were fabricated by an ultrasonic coating technique with 0.6 mg Pt.cm(-2) catalyst loading for both anode and cathode. The crosslinked membranes were tested in a single HT-PEMFC with a 5 cm(2) active area at 165 degrees C without humidification. PBI/BADGE crosslinked membranes demonstrated stability and high performance on single cell HT-PEMFC tests. The maximum power density for PBI/BADGE was determined as 0.123 W. cm(-2). As a result, the experimental results suggested that the PBI/ BADGE and PBI/DBpX cross-linked membranes are promising electrolyte options for HT-PEMFC. (C) 2017 Elsevier Ltd. All rights reserved.Article Citation Count: 133Polybenzimidazole based nanocomposite membranes with enhanced proton conductivity for high temperature PEM fuel cells(Pergamon-elsevier Science Ltd, 2017) Devrim, Yılser; Uregen, Nurhan; Devrim, Yilser; Energy Systems EngineeringIn this study, phosphoric acid doped PBI nanocomposite membranes were prepared by dispersion of various amounts of inorganic nanoparticles in PBI polymer followed by phosphoric acid (H3PO4) doping for high temperature proton exchange membrane fuel cells (HT-PEMFC). All of the PBI composite membranes were cast from the same FBI polymer with the same molecular weight. Titanium dioxide (TiO2), silicon dioxide (SiO2) and inorganic proton conductor zirconium phosphate (ZrP) were used as inorganic fillers. The PBI based composite membranes were characterized in terms of their acid uptake and acid leaching properties, mechanical properties, chemical stabilities in N-N Dimethylacetamide (DMAc) and impedance analyses. Thermal gravimetric analysis confirmed the improved thermal stability of the PBI composite membranes. The existence of inorganic fillers was improved the acid retention capability. Electrochemical Impedance Spectroscopy (EIS) showed that the introduction of 5 wt. % SiO2 or 5 wt. % ZrP helps to increase proton conductivity. The composite membrane with TiO2 retained low conductivity values than pristine PBI and this is a result of its non-uniform membrane structure. The highest proton conductivity of 0.200 S/cm was obtained for PBI/ZrP composite membrane with the highest value of H3PO4 doping level. Nyquist plots are drawn for all the membranes at different temperatures and the plots showed good fit with Randel's circuit. As a result the experimental results suggested that the PBI based composite membranes may be a promising electrolyte used in HT-PEMFC. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.