Browsing by Author "Tunc, Yahya"
Now showing 1 - 2 of 2
- Results Per Page
- Sort Options
Article Citation Count: 52Biomechanical comparison of implant retained fixed partial dentures with fiber reinforced composite versus conventional metal frameworks: A 3D FEA study(Elsevier, 2011) Erkmen, Erkan; Meric, Gokce; Kurt, Ahmet; Tunc, Yahya; Eser, AtilimFiber reinforced composite (FRC) materials have been successfully used in a variety of commercial applications. These materials have also been widely used in dentistry. The use of fiber composite technology in implant prostheses has been previously presented, since they may solve many problems associated with metal alloy frameworks such as corrosion, complexity of fabrication and high cost. The hypothesis of this study was that an FRC framework with lower flexural modulus provides more even stress distribution throughout the implant retained fixed partial dentures (FPDs) than a metal framework does. A 3-dimensional finite element analysis was conducted to evaluate the stress distribution in bone, implant-abutment complex and prosthetic structures. Hence, two distinctly different models of implant retained 3-unit fixed partial dentures, composed of Cr-Co and porcelain (M-FPD model) or FRC and particulate composite (FRC-FPD model) were utilized. In separate load cases, 300 N vertical, 150 N oblique and 60 N horizontal forces were simulated. When the FRC-FPD and M-FPD models were compared, it was found that all investigated stress values in the M-FPD model were higher than the values in the FRC-FPD model except for the stress values in the implant-abutment complex. It can be concluded that the implant supported FRC-FPD could eliminate the excessive stresses in the bone-implant interface and maintain normal physiological loading of the surrounding bone, therefore minimizing the risk of peri-implant bone loss due to stress-shielding. (C) 2010 Elsevier Ltd. All rights reserved.Article Citation Count: 22Influence of prosthesis type and material on the stress distribution in bone around implants: A 3-dimensional finite element analysis(Elsevier Taiwan, 2011) Meric, Gokce; Erkmen, Erkan; Kurt, Ahmet; Tunc, Yahya; Eser, AtilimBackground/purpose: The design and materials of a prosthesis affect the loading of dental implants and deformation of the bone. The aim of the study was to evaluate the effects of prosthesis design and materials on the stress distribution of implant-supported prostheses. Materials and methods: A 3-dimensional finite element analysis method was selected to evaluate the stress distribution in the bone. Three different models were designed as follows: a 3-unit implant-supported fixed partial denture (FPD) composed of a metal framework and porcelain veneer with (M2) or without a cantilevered extension (M1) and an FPD composed of a fiber-reinforced composite (FRC) framework and a particulate composite veneer without a cantilevered extension (M3). In separate load cases, 300-N vertical, 150-N oblique, and 60-N horizontal forces were applied to the prostheses in the models. von Mises stress values in the cortical and cancellous bone were calculated. Results: In cortical bone, the highest von Mises stresses were noted in the M2 Model with a vertical load; whereas, higher stresses were observed in the M1 Model with horizontal and oblique loads. The lowest stress values were determined in the M3 Model for all loading conditions. In cancellous bone, decreased stress values were found with all 3 models under the applied loads. Conclusions: Prosthesis design and materials affect the load-transmission mechanism. Although additional experimental and clinical studies are needed, FRC FPDs can be considered a suitable alternative treatment choice for implant-supported prostheses. Within the limitations of the study, the 3-unit FPD supported by 2 implants with a cantilevered extension revealed acceptable stress distributions. Copyright (C) 2011, Association for Dental Sciences of the Republic of China. Published by Elsevier Taiwan LLC. All rights reserved.