Browsing by Author "Sadhu, Veera"
Now showing 1 - 2 of 2
- Results Per Page
- Sort Options
Article Citation Count: 15Development of Poly(vinyl alcohol) (PVA)/Reduced Graphene Oxide (rGO) Electrospun Mats(Amer Scientific Publishers, 2019) Şaşmazel, Hilal Türkoğlu; Sadhu, Veera; Sasmazel, Hilal Turkoglu; Metallurgical and Materials EngineeringIn this study, electrospun reduced graphene oxide (rGO) and poly(vinyl alcohol) (PVA) nanocomposites were developed with the concentration of rGO as 0.5 and 1.0 wt% by dispersing rGO in the PVA solution without using any co-solvent which may cause toxic effect for possible applications like packaging and tissue engineering. Water solubility of PVA was eliminated by UV-radiation crosslinking method. SEM analysis proved that continuous and bead-free nanofibers were obtained by electrospinning process and all electrospun mats had similar fiber characteristics with homogeneous fiber morphology. The average fiber diameter (nm), inter-fiber pore size (mu m) and the porosity (%) were increased with rGO incorporation. Additionally, enhanced tensile properties was achieved by rGO addition as the highest tensile strength was obtained as similar to 5 MPa for electrospun PVA+ 1.0 wt% rGO nanocomposites. ATR-FTIR analyses showed that there was a relatively strong interfacial interaction between rGO and PVA. Moreover, the thermal stability of obtained nanocomposites was enhanced by rGO addition without changing the crystal structure of PVA proved by XRD analyses. Also, improved electrical conductivity of the nanocomposites was obtained by rGO content as the highest conductivity (similar to 11 mu S.cm(-1)) was measured for electrospun PVA+ 1.0 wt% rGO.Article Citation Count: 16Preparation of electrospun PCL-based scaffolds by mono/multi-functionalized GO(Iop Publishing Ltd, 2019) Şaşmazel, Hilal Türkoğlu; Sadhu, Veera; Sasmazel, Hilal Turkoglu; Metallurgical and Materials EngineeringIn the present study, sythetic biodegradable polymer poly(epsilon-caprolactone) (PCL) and graphene oxide (GO) were combined together to prepare 3D, composite tissue scaffolds (PCL/GO scaffolds) by using electrospinning technique. Also, the influence of Gly-Arg-Gly-Asp-Ser-Pro (GRGDSP) and/or thiophene (Th) modified GO on the composite PCL/GO mats (PCL/GO, PCL/GO-GRGDSP, PCL/ GO-Th, PCL/GO-GRGDSP-Th) was further investigated. Characteristic examinations of the scaffolds were carried out by scanning electron microscope (SEM), contact angle (CA) measurements, x-ray photoelectron spectroscopy, TGA, electrical conductivity tests, phosphate buffer saline absorption and shrinkage tests and mechanical tests. All of the scaffolds were exhibited suitable bead free and uniform morphology according to SEM images. With the addition of GO, better hydrophilicity and a slight CA decrease (similar to 5 degrees) for the PCL/GO scaffolds were observed. Mechanical properties were reinforced drastically with the addition and well-dispersion of GO into PCL matrix. The incorporation of PCL and GO exhibited enhanced electrical conductivity and the highest value was found for PCL/GO-GRGDSP-Th (2%) as 15.06 mu S cm(-1). The MG-63 osteoblast cell culture studies (MTT assay, ALP activity, Alizarin-Red staining, fluorescence and SEM analyses) showed that PCL/GO-GRGDSP-Th (1%) scaffolds exhibited the highest biocompatibility performance (1.87 fold MTT absorbance value comparing with neat PCL) due to the advanced properties of GO and the biological interfaces.